米爾淘寶店| 米爾電子| 米爾微博| English

LPC43xx數據手冊(LPC4357/LPC4350等芯片手冊)

軟件大小:8.5 MB 軟件性質: 免費軟件
更新時間:2012/11/28 15:29:19 應用平臺:Win9X/Win2000/WinXP
下載次數:14360 下載來源:米爾科技
軟件語言:英文 軟件類別:開發板資料 > MYD-LPC435x/185x 開發板
下載

包括 NXP  LPC4357/LPC4350/LPC4353/LPC4337/LPC4333/LPC4330/LPC4320/LPC4310芯片手冊


The LPC43xx are ARM Cortex-M4 based microcontrollers for embedded applications which include an ARM Cortex-M0 coprocessor, up to 1 MB of flash, up to 264 kB of SRAM, advanced configurable peripherals such as the State Configurable Timer (SCT) and the Serial General Purpose I/O (SGPIO) interface, two High-speed USB controllers, Ethernet, LCD, an external memory controller, and multiple digital and analog peripherals.

The LPC43xx operate at CPU frequencies of up to 204 MHz.The ARM Cortex-M4 is a next generation 32-bit core that offers system enhancements such as low power consumption, enhanced debug features, and a high level of support block integration. The ARM Cortex-M4 CPU incorporates a 3-stage pipeline, uses a Harvard architecture with separate local instruction and data buses as well as a third bus for peripherals, and includes an internal prefetch unit that supports speculative branching.

The ARM Cortex-M4 supports single-cycle digital signal processing and SIMD instructions. A hardware floating-point processor is integrated in the core. The ARM Cortex-M0 coprocessor is an energy-efficient and easy-to-use 32-bit core which is code- and tool-compatible with the Cortex-M4 core. The Cortex-M0 coprocessor, designed as a replacement for existing 8/16-bit microcontrollers, offers up to 204 MHz performance with a simple instruction set and reduced code size.



• Cortex-M4 Processor core

– ARM Cortex-M4 processor, running at frequencies of up to 204 MHz.

– ARM Cortex-M4 built-in Memory Protection Unit (MPU) supporting eight regions.

– ARM Cortex-M4 built-in Nested Vectored Interrupt Controller (NVIC).

– Hardware floating-point unit.

– Non-maskable Interrupt (NMI) input.

– JTAG and Serial Wire Debug (SWD), serial trace, eight breakpoints, and four

watch points.

– Enhanced Trace Module (ETM) and Enhanced Trace Buffer (ETB) support.

– System tick timer.

• Cortex-M0 Processor core

– ARM Cortex-M0 co-processor capable of off-loading the main ARM Cortex-M4

application processor.

– Running at frequencies of up to 204 MHz.

– JTAG, Serial Wire Debug, and built-in NVIC.

• On-chip memory (flashless parts)

– Up to 264 kB SRAM for code and data use.


– Multiple SRAM blocks with separate bus access. Two SRAM blocks can be

powered down individually.

– 64 kB ROM containing boot code and on-chip software drivers.

– 32 bit general-purpose One-Time Programmable (OTP) memory.

• On-chip memory (parts with on-chip flash)

– Up to 1 MB on-chip dual bank flash memory with flash accelerator.

– 16 kB on-chip EEPROM data memory.

– 136 kB SRAM for code and data use.

– Multiple SRAM blocks with separate bus access. Two SRAM blocks can be

powered down individually.

– 64 kB ROM containing boot code and on-chip software drivers.

– 128 bit general-purpose One-Time Programmable (OTP) memory.

• Configurable digital peripherals

– Serial GPIO (SGPIO) interface.

– State Configurable Timer (SCT) subsystem on AHB.

– Global Input Multiplexer Array (GIMA) allows to cross-connect multiple inputs and

outputs to event driven peripherals like the timers, SCT, and ADC0/1.

• Serial interfaces

– Quad SPI Flash Interface (SPIFI) with 1-, 2-, or 4-bit data at rates of up to 60 MB

per second.

– 10/100T Ethernet MAC with RMII and MII interfaces and DMA support for high

throughput at low CPU load. Support for IEEE 1588 time stamping and advanced

time stamping (IEEE 1588-2008 v2).

– One High-speed USB 2.0 Host/Device/OTG interface with DMA support and

on-chip high-speed PHY.

– One High-speed USB 2.0 Host/Device interface with DMA support, on-chip

full-speed PHY and ULPI interface to external high-speed PHY.

– USB interface electrical test software included in ROM USB stack.

– One 550 UART with DMA support and full modem interface.

– Three 550 USARTs with DMA and synchronous mode support and a smart card

interface conforming to ISO7816 specification. One USART with IrDA interface.

– Two C_CAN 2.0B controllers with one channel each.

– Two SSP controllers with FIFO and multi-protocol support. Both SSPs with DMA

support.

– One SPI controller.

– One Fast-mode Plus I2C-bus interface with monitor mode and with open-drain I/O

pins conforming to the full I2C-bus specification. Supports data rates of up to

1 Mbit/s.

– One standard I2C-bus interface with monitor mode and with standard I/O pins.

– Two I2S interfaces, each with DMA support and with one input and one output.

• Digital peripherals

– External Memory Controller (EMC) supporting external SRAM, ROM, NOR flash,

and SDRAM devices.

– LCD controller with DMA support and a programmable display resolution of up to

1024H  768V. Supports monochrome and color STN panels and TFT color

panels; supports 1/2/4/8 bpp Color Look-Up Table (CLUT) and 16/24-bit direct pixel

mapping.

– Secure Digital Input Output (SD/MMC) card interface.

– Eight-channel General-Purpose DMA (GPDMA) controller can access all

memories on the AHB and all DMA-capable AHB slaves.

– Up to 164 General-Purpose Input/Output (GPIO) pins with configurable

pull-up/pull-down resistors.

– GPIO registers are located on the AHB for fast access. GPIO ports have DMA

support.

– Up to eight GPIO pins can be selected from all GPIO pins as edge and level

sensitive interrupt sources.

– Two GPIO group interrupt modules enable an interrupt based on a programmable

pattern of input states of a group of GPIO pins.

– Four general-purpose timer/counters with capture and match capabilities.

– One motor control Pulse Width Modulator (PWM) for three-phase motor control.

– One Quadrature Encoder Interface (QEI).

– Repetitive Interrupt timer (RI timer).

– Windowed watchdog timer (WWDT).

– Ultra-low power Real-Time Clock (RTC) on separate power domain with 256 bytes

of battery powered backup registers.

– (Parts with on-chip flash only): Event recorder with three inputs to record event

identification and event time; can be battery powered.

– Alarm timer; can be battery powered.

• Analog peripherals

– One 10-bit DAC with DMA support and a data conversion rate of 400 kSamples/s.

– Two 10-bit ADCs with DMA support and a data conversion rate of 400 kSamples/s.

Up to eight input channels per ADC.

• Security (LPC43Sxx only)

– AES decryption programmable through an on-chip API.

– Two 128-bit secure OTP memories for AES key storage and customer use.

– Random number generator (RNG) accessible through AES API.

– Unique ID for each device.

• Clock generation unit

– Crystal oscillator with an operating range of 1 MHz to 25 MHz.

– 12 MHz Internal RC (IRC) oscillator trimmed to 1 % accuracy over temperature

and voltage.

– Ultra-low power Real-Time Clock (RTC) crystal oscillator.

– Three PLLs allow CPU operation up to the maximum CPU rate without the need for

a high-frequency crystal. The second PLL is dedicated to the High-speed USB, the

third PLL can be used as audio PLL.

– Clock output.

• Power

– Single 3.3 V (2.2 V to 3.6 V) power supply with on-chip DC-to-DC converter for the

core supply and the RTC power domain.

– RTC power domain can be powered separately by a 3 V battery supply.

– Four reduced power modes: Sleep, Deep-sleep, Power-down, and Deep

power-down.

– Processor wake-up from Sleep mode via wake-up interrupts from various

peripherals.

– Wake-up from Deep-sleep, Power-down, and Deep power-down modes via

external interrupts and interrupts generated by battery powered blocks in the RTC

power domain.

– Brownout detect with four separate thresholds for interrupt and forced reset.

– Power-On Reset (POR).

– Available as LBGA256, TFBGA180, and TFBGA100 packages and as LQFP208

and LQFP144 packages.





開發板資料

ARM開發工具

ARM工具手冊

資料下載

軟件例程

演示視頻

HMI資料

充電樁資料

工控板資料

本類下載TOP10

相關文章

常見問題解答

北京pk10开奖结果查询 麻将来了安卓手机 幸运飞艇怎么看走势图 Playboy黄金 捕鱼王最新版 手机上好玩的棋牌游 3分pk10彩票 黑龙江36选7 韩国福彩快乐8xxdc 拿过意甲冠军的球队 极速赛车群 今天黑龙江22选5开奖 皇冠比分app